The wire mesh has great performance characteristics. If you are not used to it, you should know it is not comprehensive. However, it is suggested that you do not know too much about the theory, because you can know how to use the effect of wire mesh in practice. So let's let Xiaobian tell you about the use of steel mesh.

　　該鋼網片具有良好的抗震效果。鋼筋網片是由縱向鋼筋和橫向鋼筋按一定的距離和角度焊接而成的網片。按原料可分為:冷軋帶肋網片、冷拉光滑圓鋼網片、熱軋帶肋網片，在冷軋帶肋網片期間得到廣泛應用。根據鋼筋的商標、直徑、長度和距離，將鋼網片分為常規鋼網片和非定制鋼網片。

　　The steel mesh has good seismic effect. Reinforcement mesh is welded by longitudinal reinforcement and transverse reinforcement according to a certain distance and angle. According to the raw materials, it can be divided into cold-rolled rib mesh, cold drawn smooth round steel mesh and hot-rolled rib mesh, which are widely used in cold-rolled rib mesh. According to the trademark, diameter, length and distance of reinforcement, the steel mesh is divided into conventional steel mesh and non customized steel mesh.

　　鋼網板一般采用CRB550級冷軋帶肋鋼筋或GB1499規則商標的熱軋帶肋鋼筋。鋼網板直徑4-14mm，可采用0.5mm的漸進直徑?？紤]到運輸條件，焊接網的長度和寬度不能分別超過12m和3.4m。

　　Crb550 cold rolled ribbed steel bars or gb1499 hot rolled ribbed steel bars are generally used for steel mesh plates. The diameter of the steel mesh plate is 4-14mm, and the progressive diameter of 0.5mm can be used. Considering the transportation conditions, the length and width of the welding network shall not exceed 12m and 3.4m respectively.

　　焊接網生產方向鋼筋(或縱向鋼筋)的距離宜為100、150、200毫米，其他方向鋼筋的一般距離為100、150、200、300毫米，有時可達400毫米。當水平鋼為單鋼焊接網時，一根細鋼筋的公稱直徑應不小于較厚鋼公稱直徑的0.6倍，即dmin銳度0.6 damx?？辜艉附泳W(wǎng)焊縫(在N)應不小于150和粗鋼筋公稱截面面積(是)的乘積。

　　The distance of steel bars (or longitudinal steel bars) in the production direction of welded mesh should be 100, 150, 200 mm, while the general distance of steel bars in other directions is 100, 150, 200, 300 mm, sometimes up to 400 mm. When the horizontal steel is single steel welded mesh, the nominal diameter of a fine steel bar shall not be less than 0.6 times of the nominal diameter of the thicker steel, that is, the Dmin sharpness is 0.6 damx. The shear welded net weld (in n) shall not be less than the product of 150 and the nominal section area of the coarse reinforcement.

　　保證工程質量:鋼網由自動化、智能化生產線生產，本廠嚴格控制質量。嚴格控制格柵尺度、鋼筋標準和質量。避免人工裝訂網的損耗，裝訂不牢固，裝訂誤差和偷工減料。該網架鋼性好，彈性好，間距均勻，焊接點強度高。從而大大提高了工程質量。

　　Ensure the quality of the project: the steel mesh is produced by the automatic and intelligent production line, and the factory strictly controls the quality. Strictly control the grid size, reinforcement standard and quality. Avoid the loss of manual binding net, binding is not firm, binding error and Jerry building. The grid structure has good rigidity, good elasticity, uniform spacing and high strength of welding points. Thus greatly improving the quality of the project.

　　鋼絲網片可以提高抗震和抗裂功能:焊接鋼網的縱向和橫向酒吧形成一個網絡結構,因此具有良好的粘結和錨固與具體的財產,可以均勻分布和公認的負載,可以明顯改善鋼筋混凝土結構的抗震和抗裂功能。根據實際試驗，道路鋪設焊接鋼網比人工綁扎網，可減少75%以上的裂縫。

　　The steel mesh can improve the anti-seismic and anti crack functions: the longitudinal and transverse bars of welded steel mesh form a network structure, so it has good bonding and anchoring with specific properties, can evenly distribute and recognized loads, and can significantly improve the anti-seismic and anti crack functions of reinforced concrete structures. According to the actual test, more than 75% of the cracks can be reduced when the welded steel mesh is laid on the road compared with the manual binding mesh.